Capacitor - 100uF 25v Radial Lead
Part # CAP100UF25VRAD
Condition: New
Electrolytic capacitor for many Bally and Williams pinball games. Found on power supply board in early Williams... more
|
|
Capacitor - 100uF 35v Radial Lead
Part # CAP100UF35VRAD
Condition: New
Electrolytic capacitor for PC boards in many makes/models of games. Rated at 100uF 35v. Measures 5/16 x 15/32 inches (8mm x... more
|
|
Capacitor - 150uF 160v Axial Lead
Part # CAP150UF160VAXL
Condition: New
Discontinued - use # CAP150UF160VRAD (radial lead cap) as replacement, and bend... more
|
|
Capacitor - 15,000uF 25v Radial Lead (21mm x 51mm)
Part # CAP15KUF25VRADSI
Condition: New
Replacement electrolytic filter capacitor for power supply on many applications including: Bally/Williams WPC... more
|
|
Power Cord - Grounded - 7-1/2 Foot 18 Gauge Round Black w/ Female IEC Plug End
Part # COR003
Condition: New
7-1/2 foot long power cord, black, with grounded 3-prong plug end (wall plug), and 3-prong IEC female connector plug on the... more
|
|
Score Display - Dot Matrix 128 x 32 - Glass Hi-Voltage
Part # DMD001
Condition: New
New 128 x 32 dot-matrix score display unit. Used in many later-model Bally, Williams, Gottlieb, Data East, Sega, and Stern... more
|
|
Fuse Kit - Bally / Williams WPC-89 Games (1990-1995) (SEE NOTES)
Part # FKWPC
Condition: New
Fuse kit with 12 common fuses for Bally and Williams WPC-89 games made from approx. 1990-1995. ... more
|
|
3/4-Amp Fuse (5-PACK) - Fast-Blow (AGC) 1-1/4 x 1/4 Inch
Part # FUSE3/4A-5PK
Condition: New
5 piece set of glass fuses, fast-blow. 3/4 amp. AGC series. 3AG type measuring 1/4 x 1-1/4 inches (6mm x 32mm). Rated for use... more
|
|
8-Amp Fuse (5-PACK) - Fast-Blow (AGC) 1-1/4 x 1/4 Inch
Part # FUSE8A-5PK
Condition: New
Set of 5 glass fuses, fast-blow. 8 amp. AGC series. 3AG type measuring 1/4 x 1-1/4 inches (6mm x 32mm). Rated for use up to 250... more
|
|
3/8-Amp Fuse (5-PACK) - Slow-Blow (MDL) 1-1/4 x 1/4 Inch
Part # FUSE3/8ASB-5PK
Condition: New
Set of 5 glass fuses, slow-blow. MDL series. 3AG type measuring 1/4 x 1-1/4 inches (6mm x 32mm). Rated for use up to 250 volts.
|
|
2-1/2-Amp Fuse (5-PACK) - Slow-Blow (MDL) 1-1/4 x 1/4 Inch
Part # FUSE2.5ASB-5PK
Condition: New
Set of 5 glass fuses, slow-blow. MDL series. 3AG type measuring 1/4 x 1-1/4 inches (6mm x 32mm). Rated for use up to 250... more
|
|
3-Amp Fuse (5-PACK) - Slow-Blow (MDL) 1-1/4 x 1/4 Inch
Part # FUSE3ASB-5PK
Condition: New
Set of 5 glass fuses, slow-blow. MDL series. 3AG type measuring 1/4 x 1-1/4 inches (6mm x 32mm). Rated for use up to 250... more
|
|
5-Amp Fuse (5-PACK) - Slow-Blow (MDL) 1-1/4 x 1/4 Inch
Part # FUSE5ASB-5PK
Condition: New
Set of 5 glass fuses, slow-blow. MDL series. 3AG type measuring 1/4 x 1-1/4 inches (6mm x 32mm). Rated for use up to 250... more
|
|
7-Amp Fuse (5-PACK) - Slow-Blow (MDL) 1-1/4 x 1/4 Inch
Part # FUSE7ASB-5PK
Condition: New
Set of 5 glass fuses, slow-blow. MDL series. 3AG type measuring 1/4 x 1-1/4 inches (6mm x 32mm). Rated for use up to 250... more
|
|
Fuse Holder for 1/4 x 1-1/4 Fuses - PCB Mount Type
Part # FUSEHLDR2
Condition: New
Replacement fuse holder for standard glass 3AG, AGC, MDL type fuses measuring 1/4 x 1-1/4 inch (7mm x 32mm), fast-acting or... more
|
|
Fuse Holder for 1/4 x 1-1/4 Fuses - Push/Twist Panel Mount
Part # FUSEHLDR4
Condition: New
Replacement fuse holder for standard glass 3AG, AGC, MDL type fuses, fast-acting or slow-blow, measuring 1/4 x 1-1/4 inch (7mm... more
|
|
5-Amp Fuse (5-PACK) - Slow-Blow Small 5mm x 20mm
Part # FUSET5.0ASB-5PK
Condition: New
Set of 5 small glass fuses, 5mm x 20mm, slow-blow. Rated for use up to 250 volts. For some late-model games (see game listing... more
|
|
Wire Harness - Coil Connector 2-Wire (Bally/Williams)
Part # H-11835
Condition: New
2-wire wiring harness with connector used to connect game wiring harness to coils on various devices including cabinet... more
|
|
Wire Harness - Transformer Secondary Wiring for some WPC Games (Bally/Williams)
Part # H-15736
Condition: New
Transformer secondary cable wiring harness with connectors. Connects from transformer in main cabinet to backbox. Used in many... more
|
|
Solenoid Cable and Connector (Bally/Williams)
Part # H-19523
Condition: New
Solenoid coil connection cable with 2 wires and 2-position female housing. NOTE: This part is mis-identified as... more
|
|
Heat Sink for TO-220 Regulator / Amplifier / Transistor
Part # HS-TO-220
Condition: New
Small heat sink designed to fit on PC boards behind TO-220 style transistor, amplifier, or regulator. Also fits TO-126 and... more
|
|
Heat Sink w/ Hardware Kit for TO-220 Regulator / Amplifier / Transistor
Part # HS-TO-220-KIT
Condition: New
Small heat sink with mounting hardware. Designed to fit on PC boards behind TO-220 style transistor, amplifier, or regulator.... more
|
|
LM323K 5V Voltage Regulator
Part # LM323K
Condition: New
Discontinued - use # LM323KA as replacement. Type LM323K for use in 5v power supply... more
|
|
5V Voltage Regulator - LM323K Replacement (SEE NOTES)
Part # LM323KA
Condition: New
Modern solid-state replacement switching voltage regulator that replaces the obsolete and hard-to-find LM323K. TO-3 footprint.... more
|
|
LM323K 5V Voltage Regulator (Used / Reconditioned - SEE NOTE)
Part # LM323KU
Condition: Used/Reconditioned
Used LM323K voltage regulator. Working unit, pulled from used equipment, and cleaned/tested. ... more
|
|
LM339 Voltage Comparator IC
Part # LM339
Condition: New
Voltage comparitor IC. Quad comparator (has 4 separate circuits inside). 16-pin DIP package. Many pinball applications,... more
|
|
LM1875T Amplifier IC
Part # LM1875T
Condition: New
LM1875T is the replacement amplifier as used in many later-model Bally/Williams pinball games that feature computer-controlled... more
|
|
LM7805CT Voltage Regulator - 5 Volt - TO-220-3 Case
Part # LM7805CT
Condition: New
Linear 5v voltage regulator in TO-220 case. Rated at 1 amp. Ships as LM7805CT. Commonly found on sound boards in older... more
|
|
MC14584 CMOS Hex Schmitt Trigger IC
Part # MC14584
Condition: New
CMOS hex Schmitt trigger IC used on circuit boards in some electronic pinball games. Replaces CD4584, CD4584BCN, Bally/Williams... more
|
|
Transistor - MC34064
Part # MC34064
Condition: New
4.61 volt under-voltage sensing transistor, TO-92 package. Used as U10 on WPC MPU boards in reset startup circuit. Replaces... more
|
|
Microswitch Body - Small - With/Without Diode
Part # MICROSWITCH
Condition: New
Replacement microswitch body for most applications in many pinball games from mid-1980s on up. Bare microswitch body only-... more
|
|
MJE15030 Transistor
Part # MJE15030
Condition: New
High-voltage NPN bipolar transistor, max. ratings 8 amps, 150 volts, 50 watts. Can substitute for older obsolete... more
|
|
MJE15031 Transistor
Part # MJE15031
Condition: New
High-voltage PNP bipolar transistor, max. ratings 8 amps, 150 volts, 50 watts. Can substitute for older obsolete... more
|
|
Z-Connector 0.156 Inch Spacing - 7-Pin Male/Male
Part # MWWS156-1607
Condition: New
7-pin male/male feedthrough Z connector, 0.156-inch pin spacing, high-temperature black plastic insulator, breakaway design.... more
|
|
Z-Connector 0.156 Inch Spacing - 10-Pin Male/Male
Part # MWWS156-1610
Condition: New
10-pin male/male feedthrough Z connector, 0.156-inch pin spacing, high-temperature black plastic insulator, breakaway... more
|
|
Opto Switch Emitter Element (LED) (SEE NOTES)
Part # OPTO_EMITTER
Condition: New
Opto emitter element (infrared LED) for 12-volt opto switch pairs used in some makes/models (SEE NOTES BELOW). This is the... more
|
|
Opto Switch Receiver Element (SEE NOTES)
Part # OPTO_RECEIVER
Condition: New
Opto receiver element (light-activated photo transistor) for opto switch pairs used in some makes/models (SEE NOTES BELOW).... more
|
|
Connector Housing Terminal - 0.062 Inch Round Male (10-PACK)
Part # PINM062-10PK
Condition: New
Set of 10 terminals. Round male crimp / solder pin for 0.062 inch connector housings. Replaces Molex # 02-06-2103 and... more
|
|
Connector Housing Terminal - 0.062 Inch Round Female (10-PACK)
Part # PINF062-10PK
Condition: New
Set of 10 terminals. Round female crimp / solder pin for 0.062 inch connector housings. Replaces Molex # 02-06-1103 and... more
|
|
Line Cord Plug End - Grounded 3-Prong
Part # PLUG3PRONG
Condition: New
For all makes and models of games. If you own an electronic (1977 or newer) pinball machine or video game, your game should be... more
|
|
Line Cord Plug End - Grounded 3-Prong (UK / Euro)
Part # PLUG3PRONG220V
Condition: New
Grounded line cord end for use in the U.K. and other European locations. Includes protective fuse built-in. Easy to replace on... more
|
|
Ribbon Cable Set - Some WPC-89 Games (Bally/Williams) (5 pcs)
Part # RCS6A
Condition: New
5-piece ribbon cable set comprised of the inter-board cables used in some Bally/Williams WPC-89 games made between approx. 1992... more
|
|
Power Rectifier- 35 amp 200v - Wire Leads
Part # REC3502W
Condition: New
Discontinued - use # REC3504W as replacement. Bridge rectifier for use in many... more
|
|
Power Rectifier- 35 amp 400v - Wire Leads
Part # REC3504W
Condition: New
Heavy-duty replacement rectifier for most electronic solid-state (SS) pinball games- old and new models. Rated at 35 amps, 400... more
|
|
0-ohm Resistor - 1/4-Watt
Part # RES0-1/4W
Condition: New
Standard carbon-film type resistor, 1/4-watt. Replaces Bally / Williams # 5010-09534-00 and similar others. Zero ohm... more
|
|
56-ohm Resistor - 1/4-Watt Carbon Film 5% Tolerance
Part # RES56-1/4W
Condition: New
Standard carbon-film type resistor, 1/4-watt, 5% tolerance. Replaces Bally/Williams # 5010-10171-00. 56-ohm resistor... more
|
|
560-ohm Resistor - 1/4-Watt Carbon Film 5% Tolerance
Part # RES560-1/4W
Condition: New
Standard carbon-film type resistor, 1/4-watt, 5% tolerance. Replaces Bally/Williams # 5010-08992-00. 560-ohm 5% resistor... more
|
|
Service Outlet - Cabinet Power 115 VAC
Part # SER001
Condition: New
Clip-in service outlet for power interface box/panel in most late-model domestic (U.S. / North America) makes and models of... more
|
|
Leaf Switch - 2-Lug - Slingshot Bumper / Rebound (Bally/Williams)
Part # SW-1A-114
Condition: New
2-blade leaf switch for many electronic solid-state (SS) pinball games. Installed on slingshot bumpers and rebound scoring... more
|
|
Leaf Switch Set w/ Brackets and Diode - Slingshot (2pcs) - Brackets Forward (Bally/Williams)
Part # SW-1A-114-120-BKT-1
Condition: New
Mounting brackets face forward on both switches on this item. Set of 2 leaf switches riveted to 90-degree mounting... more
|
|
Leaf Switch - Tilt w/ Weighted Blade (Bally/Williams)
Part # SW-1A-117
Condition: New
Tilt switch for many older models.
|
|
Leaf Switch - 3-Lug - Slingshot Bumper / Rebound (Bally/Williams)
Part # SW-1A-120
Condition: New
3-blade leaf switch for many electronic solid-state (SS) pinball games for slingshot bumpers and rebound scoring switches... more
|
|
Flipper End-of-Stroke Switch - Bally/Williams Games (Late)
Part # SW-1A-194
Condition: New
Low-voltage flipper EOS switch for later-model Bally and Williams games that have the Fliptronics flipper control system... more
|
|
Switch Stack - Pop Bumper Single Contact (Bally/Williams)
Part # SW-11A-37
Condition: New
Single contact switch stack for pop bumpers in later-model Bally and Williams games. Also fits early Bally or Stern electronic... more
|
|
TIP36C Transistor
Part # TIP36C
Condition: New
PNP bipolar power transistor, TO-218 (SOT-93, TO-3P) case. Rated at 100v, 25a. Large, heavy-duty transistor for many... more
|
|
TIP102 Transistor
Part # TIP102
Condition: New
NPN driver transistor for many solenoid, flashlamp, and flipper devices in several makes/models of games- old and new. ... more
|
|
TIP107 Transistor
Part # TIP107
Condition: New
PNP Darlington driver transistor commonly found in lamp matrix driver circuitry for driving lamp columns/rows in Williams,... more
|
|
TIP121 Transistor
Part # TIP121
Condition: New
NPN driver transistor for use with many solenoid and flashlamp circuits. Can be used in older games with lower coil voltages... more
|
|
TIP122 Transistor
Part # TIP122
Condition: New
NPN driver transistor rated at 100vdc, 5 amps. Drives many solenoid, flashlamp, and flipper devices. Can be... more
|
|
TL084 J-Fet Quad Op Amp IC
Part # TL084
Condition: New
J-fet quad op-amp IC used in many later-model Bally and Williams pinball games. Replaces Bally/Williams # 5370-12730-00. Ships... more
|
|
ULN2803A Driver IC
Part # ULN2803A
Condition: New
Switch matrix driver IC for all Bally/Williams WPC-89, WPC-S, WPC-95, and Pinball 2000 games (1990-1999 - see game listing... more
|
|
Yamaha YM2151 Sound Generator IC
Part # YM2151
Condition: New
24-pin DIP sound generator chip used on sound boards in some later-model pinball games. Replaces Bally/Williams # 5370-11086-00... more
|
|
Tilt Bob Assembly 3pcs (Bally/Williams)
Part # 20-6502-SET
Condition: New
3-piece tilt bob assembly including smooth rod, bob, and adjustable Tinnerman nut. Found in most later-model... more
|
|
Plasti Dip Rubber Coating - 14.5oz Can - Yellow
Part # PLASTIDIP-Y
Condition: New
Excellent for re-coating playfield prop sticks and lockdown bar latch handles! Plasti Dip is a liquid coating that air-dries to... more
|
|
Security Torx Bit Set (7pcs)
Part # BITSET2
Condition: New
7-piece driver bit set for security Torx screws as used on many late-model games. These bits fit standard Torx head screws, and... more
|
|
Pinball Parts
