Eight Ball Deluxe (Bally) Pinball Machine # 5309 - Restored/Upgraded:
Price: $12,495.00 Free Shipping *
Status: Out of Stock
Part #: GAME_EBD5309
Condition: Fully Restored
|
|
|
156 hour full professional restoration and reconditioning, including new reproduction playfield (clearcoated), full cabinet repaint, new backglass, new playfield plastics set, full LED conversion, and much more. Total of $
4,055.26
in new parts installed.

| 1) The mounting of the two large plastics at the top left and right of the playfield has been changed. These are the pieces over the left inline drop targets, and right 8-ball drop target.
From the factory, Bally mounted these plastics using fifteen 2-inch Philips-head screws that went down through the upper plastic and also through 2 clear plastic ball guides below (3 pieces each side = 6 pieces total). This is a really messy and imprecise setup, as it makes for a lot of work to remove/reinstall these plastics when doing simple maintenance (playfield cleaning, light bulb replacement, rubber ring replacement, etc). And these parts never seem to line up correctly either.
What we've done is to get rid of the fifteen individual screws that originally held all 6 of these pieces together and mount the 4 lower clear plastic pieces (ball guides) to the playfield with studs and spacers. This makes them stay in place when the upper (cover) plastics are removed. The cover plastics are simply held to the tops of the studs with common white nylon cap nuts which are quick-and-easy to remove and re-install. Makes maintenance so much easier! We have to wonder why they didn't do it this way from the factory.
|
| 2) The clear ball guide plastics included in the reproduction plastics set are very thin (thinner than factory originals) and just won't hold up to pin balls during play without quickly cracking and breaking.
We had some thicker replacements custom-made from 0.092-inch clear Polycarbonate which are much stronger, and even thicker than factory originals, and will stand up much better to heavy pin balls. 4 of these pieces are used under the 2 large upper plastics to guide the ball.
|
| 3) The mounting of the return lane guides at the bottom of the playfield has been "re-imagined".
Originally these were a 2-level assembly with a plastic guide on the bottom that came in contact with the ball, and a stainless steel metal guide on the top which had no contact with the ball.
This factory design has always appeared counter-intuitive to us: the metal guide is typically what you want on the lower portion, to hold up to all the impact from the ball. Plastic guides typically go on top (this is the way Williams did it for many years). We wonder if Bally didn't somehow get this design upside-down from the beginning, and never bothered to correct it.
You may have noticed on most original Eight Ball Deluxe games that this lower plastic guide is always broken, and you'll often see them taped-together, glued, or otherwise creatively repaired or replaced.
We've done away with the plastic guide entirely as it's simply not needed in this location, and have used just the stainless steel guide in each of the the return lanes, which holds up much better to ball activity. This is the way Williams designed the return lanes on their games for many years, and it's a tried-and-true design.
|
Item: |
Value: |
Cabinet paint stencil set | $198.95 |
Cabinet paint materials | $95.73 |
Legs refinish and paint | $85.00 |
Cabinet and backbox nylon gliders (8) | $7.98 |
Leg bolts (8) | $11.92 |
Leg bolt protective nylon washers (8) | $2.00 |
Leg levelers- heavy duty (4) | $9.96 |
Leg bolt plates- heavy duty (4) | $19.80 |
Stainless steel cabinet side rails (2) | $129.99 |
Side rail twist nails (21) | $39.69 |
Leg pad protectors (4) | $11.95 |
Flipper buttons (2) | $11.00 |
Flipper switches (2) | $27.00 |
Lockdown bar latch SEMS screws (4) | $0.76 |
Ball shooter external spring | $0.90 |
Ball shooter internal spring | $0.95 |
Ball shooter washers (3) | $1.17 |
Lockdown bar foam seal | $3.99 |
Playfield glass- tempered | $99.99 |
Dollar coin acceptor (NOS) | $30.00 |
Dollar coin door price plate | $3.99 |
Coin door decal | $8.19 |
Coin door lock | $4.95 |
Coin door volume control knob | $10.49 |
Coin door Mylar insulator for slam switch | $1.49 |
Cabinet key hook for backbox keys | $0.99 |
New tilt pendulub bob | $8.39 |
New reproduction backglass | $295.55 |
Backglass stainess steel lift channel | $39.19 |
Backbox lock | $6.95 |
Backbox bolts (4) | $5.16 |
Backbox bolt washers (4) | $1.20 |
Backbox factory inspection card (reproduction) | $3.50 |
Cabinet/backbox instruction card set (reproduction) | $25.00 |
Cabinet varistor card (reproduction) | $3.50 |
Game manual with schematics (reproduction) | $26.32 |
Fuse clips for power supply board (4) | $1.20 |
Misc fuses replaced | $3.82 |
Power supply rectifiers (2) | $15.90 |
Power supply ceramic resistor | $0.99 |
Power supply board cover standoffs (2) | $1.78 |
Power supply board cover- clear plastic | $10.00 |
Power supply board cover high voltage decal (reproduction) | $0.79 |
Backbox circuit board mounting standoffs | $3.36 |
Grounded power cord- original style | $22.49 |
Wiring harness cable ties (32) | $2.24 |
Regulator board filter capacitor kit | $10.73 |
Regulator board high voltage decal (reproduction) | $0.89 |
MPU board remote-mount battery holder, connector, batteries | $7.58 |
Antioxidant for connector pins | $2.50 |
LED score display set (5pcs) | $429.99 |
Sound/Speech Board Capacitor Kit | $26.62 |
Sound/Speech volume control pots (2) | $4.98 |
Misc electronics (transistors, resistors, etc) | $5.91 |
Misc connector pins replaced | $13.97 |
Misc connector housings replaced | $10.77 |
New Playfield (reproduction / clearcoated) | $908.00 |
Full LED kit | $149.99 |
LED Adapter Set | $63.00 |
LED Adapter Power Connector | $0.85 |
Star rollover button | $1.50 |
Rollover lane guide- blue (3) | $7.47 |
Playfield switch capacitors (13) | $6.37 |
Drop target set | $71.99 |
Switch insulator- standup target (6) | $7.50 |
Switch diodes (12) | $4.68 |
Playfield coil fuse holder | $1.99 |
Slingshot kicker coil plunger bushing (2) | $2.38 |
Slingshot kicker coil tension washer (2) | $1.82 |
Large flipper bat/shaft (3) | $22.77 |
Pop bumper bodies C-970-5 (3) | $20.97 |
Pop bumper skirts (3) | $2.97 |
Pop bumper skirt springs (3) | $2.76 |
Pop bumper switch actuator (3) | $2.67 |
Pop bumper Mylar protector rings (3) | $10.47 |
Pop bumper cap set (3pcs) | $18.00 |
Pop bumper cap collar/ring set (3pcs) | $17.67 |
Pop bumper cap screws (6) | $1.08 |
Coil sleeves | $5.52 |
Rubber ring kit | $15.70 |
Mini post- heavy-duty (2) | $8.38 |
Mini post nuts/washers | $0.74 |
Playfield post stud SMS (15) | $26.85 |
Playfield post stud MS (3) | $4.77 |
Playfield post stud spacer (15) | $4.95 |
Playfield posts- short blue (22) | $19.20 |
Playfield posts- tall blue (12) | $12.60 |
Playfield post screws (16) | $3.20 |
Playfield plastics set - screened artwork (reproduction) | $174.00 |
Playfield plastics set - clear ball guides 4pcs heavy-duty (reproduction) | $55.00 |
Playfield plastics screws (18) | $2.70 |
Playfield plastics cap nuts (27) | $7.83 |
Protective fender washers for plastics (2) | $0.50 |
Shooter lane protector | $8.89 |
Flipper rebuild kits (3) | $127.11 |
Flipper coils (3) | $62.85 |
Upper flipper actuator switch | $11.19 |
Outhole kicker coil | $25.19 |
Misc hardware (nuts/screws/washers) | $60.97 |
#555 lamp for solenoid expander | $0.25 |
Lamp socket E-120-127 (64) | $108.16 |
Lamp socket 077-5000-00 (22) | $30.58 |
Lamp socket 077-5005-00 (3) | $7.47 |
Lamp socket 077-5010-00 (11) | $23.10 |
Lamp socket 077-5026-01 | $1.59 |
Lamp socket- horizontal-mount (2) | $4.20 |
Lamp socket- medium (2) | $4.20 |
New pin ball | $2.99 |
Playfield apron & shooter gauge decals (reproduction) | $89.99 |
New plastic credit lamp lens | $2.59 |
Score & instruction card set (reproduction) | $5.00 |
| |
New Parts Total: | $4,055.26 |