- US Shipping Only. International customers can order using a US forwarding service. (more info)
|
Click to Enlarge
|
Pop Bumper Assembly - Red Ring/Cap (Bally) (SEE NOTES):
Price: $88.26 each
Status: In Stock
(4 Available)
Part #: AS-2999-R
Condition: New
|
|
|
New aftermarket reproduction pop bumper assembly for many Bally/Midway games in the 1980s (see game listing below).
Full assembly including red ring and cap, AN-26-1200 coil with diode, white bumper skirt, lamp socket with wire leads and diode, and switch with diode and capacitor pre-installed.
Installation Notes:- Plug-and-play operation. Just install and properly connect wires, and go!
- Includes capacitor across switch lugs for improved operation.
- Bumper Lamp:
- Includes #555 lamp and socket with wire leads connected to solder lugs.
- Solder lugs have a diode for controlled/switched lamp operation (optional in some games).
- Controlled/Switched Lamp: If your particular game operates the lamp in the bumper as a controlled/switched lamp (goes on/off during game play), then lamp wires need to be connected with respect to diode polarity for proper lamp operation (use your old bumper as reference, or consult your game schematic diagrams for proper wire connections).
- General Illumination Lamp: If your particular game operates the lamp in the bumper as a general-illumination lamp (always ON during play), then lamp wires will connect directly to either solder lug that have lamp socket wires attached to them (ignoring the diode). Diode lug that has no lamp socket wire will remain unconnected (or you can clip the diode out completely as well).
- Switch is pre-adjusted before shipping, but as with any pinball device with a switch, this device may require adjustments to its switch after installation, for proper operation.
- Wires from your game connecting to the switch on this device must be connected properly, with respect to switch diode orientation. Use your old bumper switch for reference, or consult your game schematic diagrams for proper wire connections.
- If you are uncomfortable installing this part, making any adjustments to it, or with making any electrical connections to it, we recommend enlisting the help of a qualified service person to assist you, to ensure proper installation and operation.
Additional Images: Click to Enlarge
Ask a question about this item
Used In The Following Games: (The list below may not be complete, and it's accuracy is not guaranteed. Contact us if you have any questions.)
BALLY: Bugs Bunny's Birthday Ball, Centaur, Centaur II, Fireball II, Harley Davidson, Motordome, more
|
Pop Bumper Assembly - No Ring/Cap (Bally) (SEE NOTES)
|
|
|
Pop Bumper Assembly - Blue Ring/Cap (Bally) (SEE NOTES)
|
Part # AS-2999-B
$88.26 each |
|
|
Pop Bumper Assembly - Orange Ring/Cap (Bally) (SEE NOTES)
|
Part # AS-2999-O
$88.26 each |
|
|
Alltek Ultimate MPU Game ROM
|
Part # ROMS474
$21.00 each |
|
|
Drop Target - White w/ Wide Top (Bally)
|
|
|
Drop Target - White w/ Horseshoe Hot Stamp - Wide Top (Bally) (USED)
|
|
|
Protector - Ball Shooter Lane (Bally) (SEE NOTE)
|
|
|
Protector P-7639 - Ball Shooter Lane (Bally) (USED)
|
|
|
Pop Bumper Skirt - Translucent Off-White NOS (Bally / Midway)
|
Part # C-790-5
$8.00 each |
|
|
Pop Bumper Skirt C-790-5 - Translucent Off-White (Bally / Midway) (USED)
|
|
|
Pop Bumper Skirt - White
|
Part # 03-6035-5
$0.99 each |
|
|
Pop Bumper Body - Ivory (Bally / Midway)
|
Part # 03-8325-5
$6.99 each |
|
|
Pop Bumper Base - Plastic (Bally / Midway)
|
Part # 03-8324-5
$31.49 each |
|
|
Pop Bumper Clear Adhesive Mylar Protector (Bally/Midway)
|
|
|
Pop Bumper Rebuild Kit - Bally/Midway Games ~1981-1991
|
Part # KIT_POPRBD3
$22.59 each |
|
|
Flipper Bat and Shaft - 3-Inch White - Bally Games (Early)
|
Part # A-3994-5
$7.59 each |
|
|
Red Flipper Rubber Ring - Large
|
Part # RINRFLP
$0.89 each |
|
|
Flipper Assembly - Linear - Right (Bally) w/ AQ-25-500/34-4500 Coil (SEE NOTES)
|
Part # ASE-1587-111-A
$115.69 each |
|
|
Flipper Rebuild Kit - Left Side Only - Bally Games 1980-1988
|
Part # FLKIT6-L
$45.58 each |
|
|
Fuse Kit - Bally Electronic Games (1977-1984) (SEE NOTES)
|
Part # FKBLYSS
$9.74 each |
|
|
Fuse Puller Tool - For Glass Fuses
|
|
|
Circuit Breaker Testing Set (6pcs)
|
|
|
Digital Multi-Meter / Multi-Tester With Leads (Color May Vary)
|
Part # METER02
$12.99 each |
|
|
Soldering Kit - 30-Watt General Purpose (4 pcs)
|
Part # SI-30-KIT
$24.29 set |
|
|
Heat Shrink Tubing Kit - 120 Pieces
|
|
|
DeoxIT Anti-Oxidant Compound D100L (2cc)
|
|
|
C23 Capacitor Replacement Kit - Bally/Stern Games (1977-1985)
|
Part # KITC23CAP
$10.77 each |
|
|
7-Digit LED Score Display (Vintage Bally/Stern)
|
|
|
#555 Lamp (Box of 10)
|
|
|
#555 Lamp (Box of 100)
|
Part # LAM555C
$20.00 box |
|
|
Light Bulb Extractor Tool
|
Part # LAMPTOOL
$0.89 each |
|
|
LED Conversion Adapter Kit for Bally / Stern Main Lamp Driver Board (SEE NOTES)
|
|
|
LED- #555 3-Element (SEE NOTES)
|
Part # LED3555
$0.99 & up |
|
|
LED- #555 4-Element (SEE NOTES)
|
Part # LED4555
$1.25 & up |
|
|
LED- #555 Dome Lens (Non-Ghosting) (SEE NOTES)
|
Part # LED555D
$1.19 & up |
|
|
LED- #555 Flexible-Lead (Non-Ghosting) (SEE NOTES)
|
Part # LED555F
$1.29 & up |
|
|
Pin Ball - 1-1/16 Inch Diameter (Standard Size)
|
|
|
Novus Polish Set - #1 #2 #3
|
|
|
Mothers California Gold Liquid Carnauba Cleaner / Wax - 16oz
|
Part # MOTHERS_WAX
$14.49 each |
|
|
Game Lock With Keys - 7/8 Inch - Double-Bitted - Keyed-Alike
|
Part # LOCKDB78A
$5.99 each |
|
|
Game Lock With Keys - 7/8 Inch - Double-Bitted - Keyed-Alike # 7500 Key- Fort/Hawk Style (SEE NOTE)
|
Part # LOCKDB78
$9.99 each |
|
|
Keyless Lock - 7/8 Inch
|
Part # LOCKHM78
$5.99 each |
|
|
Game Lock With Keys - 1-1/8 Inch - Single-Bitted
|
Part # LOCKSB118
$6.99 each |
|
|
Car License Plate Frame - Playing Pinball
|
Part # LICFRAME1
$7.99 each |
|
|