Click to Enlarge
|
Tilt Plumb Bob - 5/32 Inch Center Hole (SEE NOTE):
Price: $6.99 each
Status: In Stock
(7 Available)
Part #: 20-6502A
Condition: New
|
|
|
Graphite tilt plumb bob as used in many late-model Bally and Williams pinball games. 5/32-inch diameter center hole. Uses 1/8-inch diameter non-threaded rod and accompanying tinnerman nut. Will also fit on threaded rods (part # 12-6231 or # 12-6452) using two #6-32 wing nuts to secure (one on top, and one on bottom).
NOTE: This part was originally designed by Williams to use a thumb screw to secure it to a smooth rod. The thumb screw was used with this part on games up through approximately 1980. After that, the thumbscrew was eliminated and the plumb bob was then held to a threaded rod using two #6-32 wing nuts, one above, and one below, the plumb bob.
If your game originally used a plumb bob with thumb screw, you can order part # 535-5029-00 instead. Part # 535-5029-00 requires a 3/32-inch non-threaded rod, part # 535-5319-02.
NOTE: No returns on Electronics - all sales final.
Ask a question about this item
Used In The Following Games: (The list below may not be complete, and it's accuracy is not guaranteed. Contact us if you have any questions.)
BALLY: Addams Family, Addams Family Gold, Attack From Mars, Cactus Canyon, Champion Pub, Creature From the Black Lagoon, Doctor Who, NBA Fastbreak, Twilight Zone, World Cup Soccer '94, more
WILLIAMS: Algar, Alien Poker, Big Guns, Black Knight, Black Knight 2000, Congo, Cosmic Gunfight, Cyclone, Earthshaker, F-14 Tomcat, Firepower II, Hurricane, Junk Yard, Medieval Madness, Millionaire, Monster Bash, No Good Gofers, Tales of the Arabian Nights, Time Fantasy, Warlok, Whirlwind, more
|
Tilt Plumb Bob - 5/32 Inch Center Hole (SEE NOTE) (USED)
|
Part # 20-6502AU
$4.00 each |
|
|
Tilt Plumb Bob - 3/32-Inch Center Hole w/ Thumb Screw
|
Part # 535-5029-00
$8.39 each |
|
|
Tilt Hanger Rod / Wire - 1/8 Inch Non-Threaded
|
Part # 12-6331
$1.59 each |
|
|
Tinnerman Nut - Tilt Bob - 1/8-Inch
|
Part # 20-10289
$1.25 each |
|
|
Tilt Bob Assembly - Complete
|
Part # 95-0328-00
$29.99 each |
|
|
Tilt Hanger Rod / Wire - 3/32 x 4-3/4 Inch Non-Threaded
|
Part # 535-5319-02
$2.09 each |
|
|
Tilt Hanger Rod / Wire - 3/32 x 4-3/16 Inch Non-Threaded
|
Part # 12-6452
$1.99 each |
|
|
Tilt Hanger Rod / Wire - 7/64 x 4-3/4 Inch Threaded
|
Part # 12-6231
$1.89 each |
|
|
Wing Nut - #6-32
|
Part # HWR01-070600
$0.20 each |
|
|
Bracket - Tilt Hanger Rod Support
|
Part # 535-5221-01
$3.99 each |
|
|
Wireform Loop - Tilt Plumb Bob (Stern)
|
Part # 535-7563-01
$2.99 each |
|
|
Addams Family (Bally) Rubber Ring Kit
|
Part # KIT001
$29.06 each |
|
|
Flipper Rebuild Kit - Left Side Only - Williams Games 1980-1984
|
Part # FLKIT9-L
$23.15 each |
|
|
Flipper Rebuild Kit - Two Flippers - Bally/Williams Games 1988-1991
|
Part # FLKIT1
$58.20 each |
|
|
Flipper Rebuild Kit - Two Flippers - Bally/Williams Games 1992-1999
|
Part # FLKIT2
$39.60 each |
|
|
Flipper Bat & Shaft - 3-Inch Yellow - (Bally/Williams)
|
Part # 20-10110-6
$8.39 each |
|
|
Red Flipper Rubber Ring - Large
|
Part # RINRFLP
$0.89 each |
|
|
Fuse Kit - Williams Games L3-L7 (1977-1984) (SEE NOTES)
|
Part # FKWMSL3L7
$10.30 each |
|
|
Fuse Kit - Williams Games System 9 & 11 (1985-1990) (SEE NOTES)
|
Part # FKWMSSYS9
$15.36 each |
|
|
Fuse Kit - Bally / Williams WPC-89 Games (1990-1995) (SEE NOTES)
|
|
|
Fuse Kit - Bally / Williams WPC-95 Games (1996-1999) (SEE NOTES)
|
Part # FKWPC95
$13.90 each |
|
|
Fuse Puller Tool - For Glass Fuses
|
|
|
Circuit Breaker Testing Set (6pcs)
|
|
|
Digital Multi-Meter / Multi-Tester With Leads (Color May Vary)
|
Part # METER02
$12.99 each |
|
|
Soldering Kit - 30-Watt General Purpose (4 pcs)
|
Part # SI-30-KIT
$24.29 set |
|
|
Heat Shrink Tubing Kit - 127 Pieces
|
|
|
DeoxIT Anti-Oxidant Compound D100L (2cc)
|
|
|
Ribbon Cable Set - Standard WPC-89 Games (Bally/Williams) (4 pcs)
|
|
|
Power Supply Input Connector Repair Kit - Bally / Williams / Data East
|
|
|
System 11 MPU (Bally/Williams) Power Startup Capacitor Kit
|
Part # KITSYS11CAP
$6.67 set |
|
|
#44 Lamp (Box of 10)
|
|
|
#47 Lamp (Box of 100)
|
Part # LAM047C
$20.00 box |
|
|
Lamp Assortment Kit (#44,#555,#906,#89)
|
|
|
Light Bulb Extractor Tool
|
Part # LAMPTOOL
$0.89 each |
|
|
LED- #44 / #47 3-Element (SEE NOTES)
|
Part # LED3044
$0.99 & up |
|
|
LED- #555 4-Element (SEE NOTES)
|
Part # LED4555
$1.25 & up |
|
|
LED- #44 / #47 Dome Lens (Non-Ghosting) (SEE NOTES)
|
Part # LED044D
$1.19 & up |
|
|
LED- #555 Flexible-Lead (Non-Ghosting) (SEE NOTES)
|
Part # LED555F
$1.29 & up |
|
|
LED - #89 Flashlamp
|
|
|
LED - #906 Flashlamp
|
|
|
Pin Ball - 1-1/16 Inch Diameter (Standard Size)
|
|
|
Novus Polish Set - #1 #2 #3
|
|
|
Mothers California Gold Liquid Carnauba Cleaner / Wax - 16oz
|
Part # MOTHERS_WAX
$14.49 each |
|
|
Game Lock With Keys - 7/8 Inch - Double-Bitted - Keyed-Alike
|
Part # LOCKDB78A
$5.99 each |
|
|
Game Lock With Keys - 7/8 Inch - Double-Bitted - Keyed-Alike # 7500 Key- Fort/Hawk Style (SEE NOTE)
|
Part # LOCKDB78
$9.99 each |
|
|
Keyless Lock - 7/8 Inch
|
Part # LOCKHM78
$5.99 each |
|
|
Backbox Lock With Keys - 5/8 Inch - Single-Bitted (Black)
|
Part # LOCKSB58B
$5.99 each |
|
|
Car License Plate Frame - Playing Pinball
|
Part # LICFRAME1
$5.00 each |
|
|
Pinball Parts
